Protection of power transformer using multi criteria decision-making

Power transformers are protected by different relays that operate independently. Malfunction of each relay has a major role in reducing the reliability of the protection system. In order to mitigate the main drawbacks of the power transformer relays, an overall protection scheme is presented in this paper. This scheme proposes a novel multi criterion algorithm using decision-making based on fuzzy logic. In this paper the outputs of restricted earth fault relay and a directional check unit, are combined with the output of the differential protection relay. Therefore, problems that are pertaining to independent operation of each relay have been mitigated and the relays cover protection blind spots of each other. The improved power transformer protection (IPTP) scheme enhances the sensitivity and reliability of the power transformer protection. Extensive simulations are used to measure the effectiveness and merit of the proposed IPTP relay. The above efforts result in a multi criteria approach for protection of power transformers.     

Restructuring bank networks after mergers and acquisitions: A capacitated delocation model for closing and resizing branches

During restructuring processes, due to mergers and acquisitions, banks frequently face the problem of having redundant branches competing in the same market. In this work, we introduce a new Capacitated Branch Restructuring Model which extends the available literature in delocation models. It considers both closing down and long term operations׳ costs, and addresses the problem of resizing open branches in order to maintain a constant service level. We consider, as well, the presence of competitors and allow for ceding market share whenever the restructuring costs are prohibitively expensive.We test our model in a real life scenario, obtaining a reduction of about 40% of the network size, and annual savings over 45% in operation costs from the second year on. We finally perform a sensitivity analysis on critical parameters. This analysis shows that the final design of the network depends on certain strategic decisions concerning the redundancy of the branches, as well as their proximity to the demand nodes and to the competitor׳s branches. At the same time, this design is quite robust to changes in the parameters associated with the adjustments on service capacity and with the market reaction.     

回采巷道过断层施工技术

受断层影响,巷道过断层期间掘进速度缓慢,影响采掘接替和矿井生产效率。为了更好地促进矿井生产,以23上04轨顺掘进为研究对象,采用FLAC 3D软件模拟巷道过断层时巷道围岩变形量和塑性区范围,并将围岩划分为正常围岩、过渡带和破碎带3部分。根据模拟结果可知,围岩变形量和塑性区范围都在过渡带开始增大,在破碎带达到最大值。巷道采用后退卧底法过断层,并对断层破碎带及时采用锚网索、注浆、U型钢棚进行支护,通过联合支护相互配合,可以共同提高巷道支护强度,增强巷道顶帮抗变形能力。     

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

内插法在相关干涉仪测向体制中的应用

测向误差的减小一直以来都是无线电测向精度提高的一个难点,对于不同的测向体制所采用的减小测向误差的方法都不尽相同。本文主要介绍的是相关干涉仪测向体制的基本原理以及通过内插法的应用来减小测向误差的方法。     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

Grain mapping to freeform surface for machining using parameter-based incremental tracking method

This paper presents a novel method for mapping a texture for machining onto a freeform surface. When a grain texture designed on a 2D plane is projected onto a freeform surface simply, the texture is distorted along the curvature of the surface in the projection direction. Therefore, a method is required to suppress this distortion. The algorithm proposed in this paper rapidly generates a point cloud that represents a texture with less distortion on a simply connected parametric surface. Specifically, four equations that express local geometry constraints instead of conventional parameterization methods are presented to reduce the distortion between adjacent points on the point cloud. Solving these equations can generate grain textures on freeform surfaces. This paper examines two grain images mapped to two freeform surfaces that were prepared as case studies to demonstrate the effectiveness of the proposed method.     

Preparation of CaO granules using the granulation method

ABSTRACT

Improving the hydration resistance of CaO particle in manufacturing and application of free CaO-containing materials has practical significance. In this study, CaO granules was made from Ca(OH)₂ particles, which were fabricated by the granulation method. The results showed that the hydration resistance of the CaO granules which was prepared under 1700?r?min^?1 was the best, the CaO granules was sintered well in calcination process, the shell of CaO granules was relatively dense, which improves the hydration resistance of CaO granules, and the rate of hydration weight increment was 0.58% after placed in the air for 20 days under a temperature of 10–14°C and a relative humidity of 57–81%.     

Cost-minimization analysis of a working vacation queue with N-policy and server breakdowns

This paper investigates the N-policy M/M/1 queueing system with working vacation and server breakdowns. As soon as the system becomes empty, the server begins a working vacation. The server works at a lower service rate rather than completely stopping service during a vacation period. The server may break down with different breakdown rates during the idle, working vacation, and normal busy periods. It is assumed that service times, vacation times, and repair times are all exponentially distributed. We analyze this queueing model as a quasi-birth–death process. Furthermore, the equilibrium condition of the system is derived for the steady state. Using the matrix-geometric method, we find the matrix-form expressions for the stationary probability distribution of the number of customers in the system and system performance measures. The expected cost function per unit time is constructed to determine the optimal values of the system decision variables, including the threshold N and mean service rates. We employ the particle swarm optimization algorithm to solve the optimization problem. Finally, numerical results are provided, and an application example is given to demonstrate the applicability of the queueing model.